60mil HDPE Liner For Salt Evaporation Pond Project in Australia

60mil HDPE Liner for Salt Evaporation Pond Project in Australia

HDPE plastic lining, also known as HDPE geomembrane lining, is an ideal and cost-effective geolining material for salt evaporation ponds. HDPE plastic liner is made of high-density polyethylene with 2%~3% carbon black masterbatch, anti-aging agent, ultraviolet absorber, stabilizer and so on. HDPE smooth anti-seepage membrane has high rigidity and toughness, good mechanical strength, environmental stress crack resistance and tear resistance performance. The strength is also higher. The HDPE impermeable membrane is resistant to strong acid and alkali corrosion, oil and salt, organic solvents, etc. HDPE thickness is from 0.2mm to 4.0mm. It is widely used in civil engineering. The 60mil HDPE plastic liner is suitable for anti-seepage in special industries, and is widely used in environmental protection, sanitation, sewage treatment plants, power plant regulation tank industries, mines, hospitals, solid waste, landfills and other projects.

Question

Inquiries about geomembranes from Australian customers from the official website. Customers inquire whether our geomembrane HDPE plastic lining can be used in salt evaporation pond projects. Through the communication with the customer, the customer uses the traditional sun drying method to produce sea salt. Using the coastal beach, dams are built to open up salt ponds, and the tides are used to raise water, attracting seawater to fill the ponds, and turning into brine through sunlight evaporation. When the brine concentration evaporates to 25 Baume degrees, sodium chloride is precipitated, which is the original salt. Sea salt production uses seawater as raw material, and seawater is introduced into salt evaporation ponds through channels. With this traditional method of drying sea salt, the yield is low, and the client wants to increase the yield of the salt farm under the same conditions, thereby increasing the income.

solution

We recommend MTTVS's 60mil HDPE eco-friendly geomembrane for his salt evaporation pond project. Since the brine in the evaporation pond is corrosive and the salt is eaten by humans, it is necessary to use a high-quality 100% virgin material environmentally friendly geomembrane lining. HDPE geomembrane lining is used for anti-seepage of salt pools. Under the same weather, the daily salt output of the anti-seepage lining at the bottom of the pool is usually about 150% higher than that of the traditional drying method.

According to the size of the salt evaporation pond given by the customer, it is calculated that a 60mil HDPE geomembrane of 85,000 square meters is required. He gave the customer the cheapest price of 60mil HDPE geomembrane, shared the experience of using membrane in the evaporation pond project and exchanged the precautions and methods for laying geomembrane. Customers are very satisfied with our professional project experience and super high quality products. We provide customers with 60mil HDPE geomembrane testing technical parameters, quality certification and free samples. After more than a month of close communication, we successfully got the order.

Benefit

1. The finished product of the HDPE plastic liner is a black high-strength coil, which has high wear resistance and light absorption and heat absorption. It absorbs natural sunlight and converts it into heat energy, accelerates water evaporation, accelerates the separation of salt crystallization, and greatly increases the salt production per unit area.

2. HDPE plastic liner is environmentally friendly and food safety.

3. The HDPE plastic liner acts as an anti-seepage isolation for the salt pool, reduces impurities, maintains the purity of the salt, and increases the price of the salt.

4. HDPE geomembrane is used as the anti-seepage isolation of the salt pool to speed up the collection of crystalline salt and increase the output.

HDPE geomembrane has high strength, wear resistance, high return on investment, high return on investment, saves the land area of salt dry field, and has good economic benefits.

Installation of 60mil HDPE Geomembrane Liner for Salt Evaporation Pond in Australia

1. Carry out unpacking inspection before construction, and record and repair the defects such as mechanical damage, production injury, hole, breakage and so on. Before cutting the geomembrane, measure its relative dimensions, measure its relative dimensions, and cut it.

2. The base surface of the HDPE plastic liner construction and installation should be compacted and flat, and sharp objects such as tree roots, stones, glass, iron nails, etc. should be removed; the inner and outer corners of the base should be rounded, and the radius of the rounded corners should be ≥50cm, and the surface of the weld should be cleaned.

3. Climate requirements for geomembrane construction: generally, it should be above 5 °C. Geomembrane installation and construction should be appropriately pre-released by 2% to 5% according to the specific site conditions and the climatic conditions at that time. HDPE plastic lining should be tight at low temperature and geomembrane should be relaxed at high temperature. When the temperature is too low, it should not be applied in the environment of strong wind or rain and snow above level 4.

4. Laying of geomembrane. The overlapping width of the seam between the film and the film is 10cm~15cm, so that the direction of the seam arrangement is parallel to the toe line of the slope, that is, along the slope direction; minimize the number of welded joints. Save raw materials as much as possible. Usually in corners and deformed areas, the length of the joint should be as short as possible. Except for requirements, on slopes with a slope greater than 1:6, and within 1.5m from the top slope or stress concentration area, try not to install welds;

5. During the laying of the HDPE plastic liner, do not drag, pull hard, or pull too tightly to avoid being stabbed by sharp objects, and minimize walking and moving tools on the surface of the geomembrane. At the same time, pay attention to cover the protective layer to avoid damage to the geomembrane and cause safety accidents.

60mil HDPE smooth pond liner

salt Evaporation pond liner

pond liner production line

About MTTVS

Since its establishment in 2014, MTTVS has been providing one-stop geosynthetics products and solutions to customers around the world. Served more than 500,000 successful engineering cases worldwide. MTTVS has supplied a wide range of effective, state-of-the-art geomaterials, geotextiles, geocells, geosynthetic clay liners (GCL), drainage panels, geogrids and other geomaterials to over 100 countries. Our main customers are from UK, USA, Mexico, Australia, France, Sweden, Hong Kong, Hungary, New Zealand, Poland, Ecuador, Brazil, Pakistan, Bangladesh, Germany, Thailand, Vietnam, Malaysia, Indonesia, Singapore, Philippines, Sri Lanka, India, United Arab Emirates, Saudi Arabia, Qatar, Kenya, Ghana, Egypt, Ethiopia, Somalia, Nigeria, South Africa, Swaziland, Zambia, etc.

We develop and customize according to the technical parameters required by customers. It has a core technical team, huge production capacity, strict quality control system and professional and perfect service. We are a reliable geomembrane manufacturer.